chatgpt translation russian-english

AitalMAC-UI.md

@@ -1340,43 +1340,43 @@ The input signal on the control card is not assigned
 
 #### 1.5.1.81 81 [ECAT.16.1] TILTER VACUUM 1 IN PRESSURE
 
-The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and move the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum.
+The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and flipping the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum.
 
 #### 1.5.1.82 82 [ECAT.16.2] TILTER VACUUM 2 IN PRESSURE
 
-The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and move the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum.
+The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and flipping the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum.
 
 #### 1.5.1.83 83 [ECAT.16.3] TILTER VACUUM 3 IN PRESSURE
 
-The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and move the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum.
+The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and flippinf the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum.
 
 #### 1.5.1.84 84 [ECAT.16.4] TILTER VACUUM 4 IN PRESSURE
 
-The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and move the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum.
+The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and flipping the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum.
 
 #### 1.5.1.85 85 [ECAT.16.5] TILTER VACUUM 5 IN PRESSURE
 
-The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and move the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum.
+The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and flipping the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum.
 
 #### 1.5.1.86 86 [ECAT.16.6] TILTER VACUUM 6 IN PRESSURE
 
-The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and move the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum.
+The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and flipping the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum.
 
 #### 1.5.1.87 87 [ECAT.16.7] TILTER VACUUM 7 IN PRESSURE
 
-The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and move the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum.
+The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and flipping the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum.
 
 #### 1.5.1.88 88 [ECAT.16.8] TILTER VACUUM 8 IN PRESSURE
 
-The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and move the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum.
+The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and flipping the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum.
 
 #### 1.5.1.89 89 [ECAT.16.9] TILTER AT 0A°
 
-The input signal from the position sensor of the additional vacuum suction cups. The suction cups are raised and the machine can perform cutting and milling work.
+The input signal comes from the position sensor of the additional vacuum suction cups. The suction cups are lifted and rotated to flip the material.
 
 #### 1.5.1.90 90 [ECAT.16.10] TILTER AT 180A°
 
-The input signal from the position sensor of the additional vacuum suction cups. The suction cups are lowered and the machine can perform work on moving the material on the workbench.
+The input signal from the position sensor of the additional vacuum suction cups. The suction cups are lowered and the machine can perform work on flipping the material on the workbench.
 
 #### 1.5.1.91 91 [ECAT.16.11] FLIPPER SAFETY
 
@@ -1408,12 +1408,20 @@ The input signal on the control card is not assigned
 
 #### 1.5.1.97  REMOTE SPD+
 
+The input signal is a change in the speed of the spindle as a percentage of its initial speed.
+
 #### 1.5.1.98  REMOTE BLADE ON
 
+Input signal for turning on the spindle from the remote control
+
 #### 1.5.1.99  REMOTE SPD-
 
+The input signal is used to reduce the speed of the spindle as a percentage of its initial speed.
+
 #### 1.5.1.100  REMOTE CONFIRM
 
+The input signal for connecting the remote control
+
 #### 1.5.1.101  REMOTE Y+
 
 An input signal to enable the movement of the machine in a positive direction along the Y-axis using the remote control.
@@ -1449,7 +1457,7 @@ An input signal to enable the movement of the machine in a positive direction al
 ### 1.5.2 OUTPUT (1-32)
 
 ![1.5.2_a.png](/aitalmac-ui/1.5.2_a.png)
-A tab with the output signals from the main modules and components of the machine. The operator can use this tab to check the operation of selected commands, see how the machine is performing, and, if necessary, make adjustments.
+A tab with the output signals from the main modules and components of the machine. The operator can use this tab to check the operation of selected commands, see how the machine is performing, and, if necessary, make adjustments.Care must be taken when using the output signals, because the commands are forced and do not match the safe positions of the machine.
 
 #### 1.5.2.1 01 [ECAT.13.01] ENABLE MACHINE
 
@@ -1461,6 +1469,8 @@ Resets (reboots) the camera used for taking images of material on the workbench.
 
 #### 1.5.2.3 03 [ECAT.13.03] WATERJET ENABLE
 
+Activates the water jet. This signal is also given when the machine is turned on from the operator's menu.
+
 #### 1.5.2.4 04 [ECAT.13.04] VACUUM PUMP
 
 Activates the vacuum pump, creating a vacuum in the system. This signal is necessary for testing all vacuum suction cups. Each suction cup can be tested individually by activating its respective output signal.
@@ -1475,14 +1485,20 @@ Activates the automatic lubrication pump. The pump normally operates at set inte
 
 #### 1.5.2.7 07 [ECAT.13.07] CHILLER SWITCH
 
+Activating chiller shutdown
+
 #### 1.5.2.8 08 [ECAT.13.08] TABLE SLOW SWITCH VALVE
 
+???
+
 #### 1.5.2.9 09 [ECAT.13.09] SLAB WASH
 
 Activates the material cleaning system. This opens the water supply valve for cleaning nozzles.
 
 #### 1.5.2.10 10 [ECAT.13.10] WATERJET GUN
 
+???
+
 #### 1.5.2.11 11 [ECAT.13.11] INTERNAL WATER
 
 Enables water flow through the spindle center for milling operations. Activating this signal opens the respective water and air supply valves.
@@ -1585,95 +1601,177 @@ Activates the yellow light on the control panel. The yellow light signals that t
 
 #### 1.5.2.35 35 [ECAT.19.03] GREEN LIGHT
 
+Activates the green light on the control panel. A green light warns the operator when the machine is working.
+
 #### 1.5.2.36 36 [ECAT.19.04] WHITE LIGHT
 
+Activates the white light on the control panel. A white light warns the operator about making machine settings
+
 #### 1.5.2.37 37 [ECAT.19.05] TCP LIGHT
 
+Activates the green illumination of the switch. The green light indicates that interpolation is enabled.
+
 #### 1.5.2.38 38 [ECAT.19.06] NONE
 
+The output signal on the control board is not set
+
 #### 1.5.2.39 39 [ECAT.19.07] NONE
 
+The output signal on the control board is not set
+
 #### 1.5.2.40 40 [ECAT.19.08] NONE
 
+The output signal on the control board is not set
+
 #### 1.5.2.41 41 [ECAT.19.09] NONE
 
+The output signal on the control board is not set
+
 #### 1.5.2.42 42 [ECAT.19.10] NONE
 
+The output signal on the control board is not set
+
 #### 1.5.2.43 43 [ECAT.19.11] NONE
 
+The output signal on the control board is not set
+
 #### 1.5.2.44 44 [ECAT.19.12] NONE
 
+The output signal on the control board is not set
+
 #### 1.5.2.45 45 [ECAT.19.13] NONE
 
+The output signal on the control board is not set
+
 #### 1.5.2.46 46 [ECAT.19.14] NONE
 
+The output signal on the control board is not set
+
 #### 1.5.2.47 47 [ECAT.19.15] NONE
 
+The output signal on the control board is not set
+
 #### 1.5.2.48 48 [ECAT.19.16] NONE
 
+The output signal on the control board is not set
+
 ### 1.5.3 DOUT (1-16)
 
 ![1.5.3.png](/aitalmac-ui/1.5.3.png)
 
 #### 1.5.3.1 1 [ECAT.15.01] FLIPPER VAC 1
 
+Activates the vacuum suction cup (1) on the tile flip module.
+
 #### 1.5.3.2 42 [ECAT.15.02] FLIPPER VAC 2
 
+Activates the vacuum suction cup (2) on the tile flip module.
+
 #### 1.5.3.3 43 [ECAT.15.03] FLIPPER VAC 3
 
+Activates the vacuum suction cup (3) on the tile flip module.
+
 #### 1.5.3.4 44 [ECAT.15.04] FLIPPER VAC 4
 
+Activates the vacuum suction cup (4) on the tile flip module.
+
 #### 1.5.3.5 45 [ECAT.15.05] FLIPPER VAC 5
 
+Activates the vacuum suction cup (5) on the tile flip module.
+
 #### 1.5.3.6 46 [ECAT.15.06] FLIPPER VAC 6
 
+Activates the vacuum suction cup (6) on the tile flip module.
+
 #### 1.5.3.7 47 [ECAT.15.07] FLIPPER VAC 7
 
+Activates the vacuum suction cup (7) on the tile flip module.
+
 #### 1.5.3.8 48 [ECAT.15.08] FLIPPER VAC 8
 
+Activates the vacuum suction cup (8) on the tile flip module.
+
 #### 1.5.3.9 49 [ECAT.15.09] FLIPPER FLIP
 
+Activates a 180° rotation of the module. The command will execute without safety checks, so the operator must carefully monitor the module's position.
+
 #### 1.5.3.10 59 [ECAT.15.10] NONE
 
+The output signal on the control board is not set
+
 #### 1.5.3.11 60 [ECAT.15.11] NONE
 
+The output signal on the control board is not set
+
 #### 1.5.3.12 61 [ECAT.15.12] NONE
 
+The output signal on the control board is not set
+
 #### 1.5.3.13 62 [ECAT.15.13] NONE
 
+The output signal on the control board is not set
+
 #### 1.5.3.14 63 [ECAT.15.14] NONE
 
+The output signal on the control board is not set
+
 #### 1.5.3.15 64 [ECAT.15.15] NONE
 
+The output signal on the control board is not set
+
 #### 1.5.3.16 65 [ECAT.15.16] NONE
 
+The output signal on the control board is not set
+
 ### 1.5.4 SERVICE
 
 ![1.5.4.png](/aitalmac-ui/1.5.4.png)
 
+This section displays operational data for the machine and motors, including total running hours (machine hours), to facilitate timely maintenance.
+
 #### 1.5.4.1 MACHINE HOURS
 
+Displays the total runtime of the machine from its first activation to the most recent shutdown.
+
 #### 1.5.4.2 SPINDLE HOURS
 
+Shows the cumulative runtime of the spindle from its initial activation to the most recent shutdown.
+
 #### 1.5.4.3 WATERJET HOURS
 
+Indicates the total runtime of the waterjet motor from its first activation to the most recent shutdown.
+
 ## 1.6 Parameters
 
 ![1.6.png](/aitalmac-ui/1.6.png)
 
+The main machine parameters are divided into five tabs for easy navigation and adjustment.
+
 ### 1.6.1 General (1-18)
 
 ![1.6.1_a.png](/aitalmac-ui/1.6.1_a.png)
 
+This tab contains the primary settings for the machine.
+
 #### 1.6.1.1 Language
 
+Allows the selection of the interface language. Users can activate one of the available language options.
+
 #### 1.6.1.2 Machine
 
+Enables the selection of the machine model for parameter configuration. Activate the appropriate model to adjust settings.
+
 #### 1.6.1.3 Write debug info to the debug.txt
 
+Enabling or disabling the "Write debug information to a file" debug.txt
+
 #### 1.6.1.4 Lock page
 
-#### 1.6.1.5 Use aitalmac remote
+Enabling or disabling the ability to block a page
+
+#### 1.6.1.5 Use AitalMAC Remote
+
+Enables or disables the ability to use the AitalMAC remote control for machine operations.
 
 #### 1.6.1.6 Auto accept pnc program
 
@@ -1681,61 +1779,111 @@ Activates the yellow light on the control panel. The yellow light signals that t
 
 #### 1.6.1.8 Check B angle when Z down without Blade
 
+Enabling or disabling the ability check B angle when Z down without Blade
+
 #### 1.6.1.9 Image position is without KINS
 
 #### 1.6.1.10 Debug mode
 
 #### 1.6.1.11 GCode type for gcode page
 
+Choosing the file format for downloading the G-code program
+
 #### 1.6.1.12 Accent Color
 
+Selection of the accent color for display in the menu.
+
 #### 1.6.1.13 Primary Color
 
-#### 1.6.1.14 CNC communication rate (ms)
+Selection of the primary color for display in the menu.
+
+#### 1.6.1.14 CNC Communication Rate (ms)
+
+The communication speed of the control modules.
 
-#### 1.6.1.15 Wait time of after machine on (s)
+#### 1.6.1.15 Wait Time After Machine On (s)
 
-#### 1.6.1.16 Wait time of after finish homing (ms)
+The waiting time before using the machine after it is turned on. This allows for self-testing and system checks.
 
-#### 1.6.1.17 Linear speed
+#### 1.6.1.16 Wait Time After Finish Homing (ms)
 
-#### 1.6.1.18 Angular speed
+The waiting time after completing the homing sequence.
+
+#### 1.6.1.17 Linear Speed
+
+The linear movement speed of the machine.
+
+#### 1.6.1.18 Angular Speed
+
+The angular rotation speed of the machine.
 
 ### 1.6.1 General (19-34)
 
 ![1.6.1_b.png](/aitalmac-ui/1.6.1_b.png)
 
-#### 1.6.1.19 No tool linear speed (for A8)
+#### 1.6.1.19 No Tool Linear Speed (for A8)
+
+The linear movement speed of the machine when no tool is loaded.
+
+#### 1.6.1.20 No Tool Angular Speed (for A8)
+
+The angular rotation speed of the machine when no tool is loaded.
 
-#### 1.6.1.20 No tool angular speed (for A8)
+#### 1.6.1.21 Pick Point Radius
 
-#### 1.6.1.21 Pick point radius
+The radius of the point created as a marker (laser cross) in the imported file.
 
-#### 1.6.1.22 Laser x offset
+#### 1.6.1.22 Laser X Offset
 
-#### 1.6.1.23 Laser y offset
+The laser's offset distance along the X-axis.
 
-#### 1.6.1.24 Table corner X point (G56)
+#### 1.6.1.23 Laser Y Offset
 
-#### 1.6.1.25 Table corner Y point (G56)
+The laser's offset distance along the Y-axis.
+
+#### 1.6.1.24 Table Corner X Point (G56)
+
+The coordinate system selection for the table corner along the X-axis.
+
+#### 1.6.1.25 Table Corner Y Point (G56)
+
+The coordinate system selection for the table corner along the Y-axis.
 
 #### 1.6.1.26 X Parking Position
 
+The X-axis coordinates for parking the machine in a safe position.
+
 #### 1.6.1.27 Y Parking Position
 
+The Y-axis coordinates for parking the machine in a safe position.
+
 #### 1.6.1.28 Z Safe Position
 
+The safety position distance along the Z-axis.
+
 #### 1.6.1.29 B Safe Position
 
-#### 1.6.1.30 C safe Position
+The safety position angle along the B-axis.
 
-#### 1.6.1.31 V safe Position
+#### 1.6.1.30 C Safe Position
 
-#### 1.6.1.32 Z fingerbit probe start
+The safety position angle along the C-axis.
 
-#### 1.6.1.33 Z fingerbit probe end
+#### 1.6.1.31 V Safe Position
 
-#### 1.6.1.34 Fingerbit probe B safe
+The safety position angle along the V-axis.
+
+#### 1.6.1.32 Z Fingerbit Probe Start
+
+The Z-axis coordinate for the start of the slow descent to the probe for measuring the installed tool's length.
+
+#### 1.6.1.33 Z Fingerbit Probe End
+
+The Z-axis coordinate for the end of the descent to the probe for measuring the installed tool's length.
+
+#### 1.6.1.34 Fingerbit Probe B Safe
+
+The B-axis angle position for performing the tool length measurement command using the probe.
 
 ### 1.6.1 General (35-50)
 
@@ -1743,79 +1891,147 @@ Activates the yellow light on the control panel. The yellow light signals that t
 
 #### 1.6.1.35 Blade probe C safe
 
+The C-axis angle for performing the blade diameter measurement using the probe.
+
 #### 1.6.1.36 Z blade probe start
 
+The Z-axis coordinate for starting the slow descent of the machine head to the probe for measuring the blade diameter.
+
 #### 1.6.1.37 Z blade probe end
 
+The Z-axis coordinate for ending the descent of the machine head to the probe for measuring the blade diameter.
+
 #### 1.6.1.38 Blade probe x position
 
+The X-axis coordinate of the probe.
+
 #### 1.6.1.39 Blade probe y position
 
+The Y-axis coordinate of the probe.
+
 #### 1.6.1.40 Blade probe z position
 
+The Z-axis coordinate of the probe.
+
 #### 1.6.1.41 Blade probe down feed
 
+The feed rate for performing the blade diameter measurement.
+
 #### 1.6.1.42 Table x point
 
+The X-axis coordinate of the table corner point.
+
 #### 1.6.1.43 Table y point
 
+The Y-axis coordinate of the table corner point.
+
 #### 1.6.1.44 Table width
 
+The width of the table.
+
 #### 1.6.1.45 Table height
 
+The height of the table.
+
 #### 1.6.1.46 Resolution
 
+The tab for selecting image resolution.
+
 #### 1.6.1.47 Use internet camera
 
+Enables or disables the use of a network camera.
+
 #### 1.6.1.48 Picture count (work for single host)
 
+Specifies the number of pictures to be taken.
+
 #### 1.6.1.49 Old camera
 
+Indicates whether the old camera is active or inactive.
+
 #### 1.6.1.50 Take X0 image position
 
+The X-axis coordinate for taking a photo.
+
 ### 1.6.1 General (51-65)
 
 ![1.6.1_d.png](/aitalmac-ui/1.6.1_d.png)
 
 #### 1.6.1.51 Take Y0 image position
 
+The Y-axis coordinate for taking a photo.
+
 #### 1.6.1.52 Take X1 image position
 
+The X-axis coordinate for taking a photo.
+
 #### 1.6.1.53 Take Yl image position
 
+The Y-axis coordinate for taking a photo.
+
 #### 1.6.1.54 Take X2 image position
 
+The X-axis coordinate for taking a photo.
+
 #### 1.6.1.55 Take Y2 image position
 
+The Y-axis coordinate for taking a photo.
+
 #### 1.6.1.56 Take X3 image position
 
+The X-axis coordinate for taking a photo.
+
 #### 1.6.1.57 Take Y3 image position
 
+The Y-axis coordinate for taking a photo.
+
 #### 1.6.1.58 Wait time for take picture
 
-#### 1.6.1.59 Piture Scale for take picture
+The waiting time for equipment preparation before taking a picture.
+
+#### 1.6.1.59 Picture Scale for take picture
+
+The scale of the image for saving and importing.
 
 #### 1.6.1.60 Safety above the stone
 
+The safety clearance above the material.
+
 #### 1.6.1.61 Wood Thickness
 
+The thickness of the workbench surface.
+
 #### 1.6.1.62 Plunge into the wood
 
+The depth of the cutting tool's plunge into the workbench.
+
 #### 1.6.1.63 Under wood table Z position
 
+The Z-axis coordinate for the position below the workbench.
+
 #### 1.6.1.64 Stone thickness
 
+The thickness of the stone material.
+
 #### 1.6.1.65 Vacuum 1 x offset
 
+The X-axis offset of vacuum cup 1 relative to the center of rotation.
+
 ### 1.6.1 General (66-81)
 
 ![1.6.1_e.png](/aitalmac-ui/1.6.1_e.png)
 
-#### 1.6.1.66 Vacuum 1 y offset
+#### 1.6.1.66 Vacuum 1 Y Offset
+
+The Y-axis offset of vacuum cup 1 relative to the center of rotation.
 
-#### 1.6.1.67 Vacuum 1 width
+#### 1.6.1.67 Vacuum 1 Width
 
-#### 1.6.1.68 Vacuum 1 height
+The width of vacuum cup 1.
+
+#### 1.6.1.68 Vacuum 1 Height
+
+The height of vacuum cup 1.
 
 #### 1.6.1.69 Vacuum 2 x offset
 
@@ -1871,7 +2087,9 @@ Activates the yellow light on the control panel. The yellow light signals that t
 
 #### 1.6.1.93 Vacuum 8 height
 
-#### 1.6.1.94 Vacuum safety over stone
+#### 1.6.1.94 Vacuum Safety Over Stone
+
+The safety clearance distance of vacuum cups above the stone material.
 
 #### 1.6.1.95 Vacuum Z position