From f026def7bd86f93d00631449a7e38d3f34a82510 Mon Sep 17 00:00:00 2001 From: Luca Toniolo Date: Wed, 15 Jan 2025 10:02:51 +0800 Subject: [PATCH] chatgpt translation russian-english --- AitalMAC-UI.md | 189 +++++++++++++++++++++++++------------------------ 1 file changed, 96 insertions(+), 93 deletions(-) diff --git a/AitalMAC-UI.md b/AitalMAC-UI.md index e4e6317..0b45cf8 100644 --- a/AitalMAC-UI.md +++ b/AitalMAC-UI.md @@ -1609,7 +1609,7 @@ Activates the white light on the control panel. A white light warns the operator #### 1.5.2.37 37 [ECAT.19.05] TCP LIGHT -Активируется зелёная подсветка выключателя. Зелёный свет показывает что интерполяции включена. +Activates the green illumination of the switch. The green light indicates that interpolation is enabled. #### 1.5.2.38 38 [ECAT.19.06] NONE @@ -1693,7 +1693,7 @@ Activates the vacuum suction cup (8) on the tile flip module. #### 1.5.3.9 49 [ECAT.15.09] FLIPPER FLIP -Активирует поворот модуля на 180°. Команда выполнится игнорируя безопасность. Оператор должен внимательно следить за положением модуля. +Activates a 180° rotation of the module. The command will execute without safety checks, so the operator must carefully monitor the module's position. #### 1.5.3.10 59 [ECAT.15.10] NONE @@ -1726,37 +1726,40 @@ The output signal on the control board is not set ### 1.5.4 SERVICE ![1.5.4.png](/aitalmac-ui/1.5.4.png) -Данные работы станка и моторов, время работы (моточасы) Для своевременно обслуживания станка. + +This section displays operational data for the machine and motors, including total running hours (machine hours), to facilitate timely maintenance. #### 1.5.4.1 MACHINE HOURS -Общее время работы станка от первого включения до последнего выключения. +Displays the total runtime of the machine from its first activation to the most recent shutdown. #### 1.5.4.2 SPINDLE HOURS -Общее время работы шпинделя от первого включения до последнего выключения. +Shows the cumulative runtime of the spindle from its initial activation to the most recent shutdown. #### 1.5.4.3 WATERJET HOURS -Общее время работы мотора от первого включения до последнего выключения. +Indicates the total runtime of the waterjet motor from its first activation to the most recent shutdown. ## 1.6 Parameters ![1.6.png](/aitalmac-ui/1.6.png) -Основные параметры станка. Разделены на пять вкладок. + +The main machine parameters are divided into five tabs for easy navigation and adjustment. ### 1.6.1 General (1-18) ![1.6.1_a.png](/aitalmac-ui/1.6.1_a.png) -Главные параметры станка. + +This tab contains the primary settings for the machine. #### 1.6.1.1 Language -Выбор языка интерфейса. Можно активировать один из доступных языков. +Allows the selection of the interface language. Users can activate one of the available language options. #### 1.6.1.2 Machine -Выбор станка для настройки параметров. Нужно активировать нужную модель станка. +Enables the selection of the machine model for parameter configuration. Activate the appropriate model to adjust settings. #### 1.6.1.3 Write debug info to the debug.txt @@ -1766,9 +1769,9 @@ Enabling or disabling the "Write debug information to a file" debug.txt Enabling or disabling the ability to block a page -#### 1.6.1.5 Use aitalmac remote +#### 1.6.1.5 Use AitalMAC Remote -Включение или отключение возможности использовать пульт дистанционного управления aitalmac +Enables or disables the ability to use the AitalMAC remote control for machine operations. #### 1.6.1.6 Auto accept pnc program @@ -1788,99 +1791,99 @@ Choosing the file format for downloading the G-code program #### 1.6.1.12 Accent Color -Выбор акцентного цвета для отображения в меню +Selection of the accent color for display in the menu. #### 1.6.1.13 Primary Color -Выбор основного цвета для отображения в меню +Selection of the primary color for display in the menu. -#### 1.6.1.14 CNC communication rate (ms) +#### 1.6.1.14 CNC Communication Rate (ms) -Скорость коммуникации модулей управления +The communication speed of the control modules. -#### 1.6.1.15 Wait time of after machine on (s) +#### 1.6.1.15 Wait Time After Machine On (s) -Время ожидания перед использованием станка после включения. (время для самотестирования и проверки) +The waiting time before using the machine after it is turned on. This allows for self-testing and system checks. -#### 1.6.1.16 Wait time of after finish homing (ms) +#### 1.6.1.16 Wait Time After Finish Homing (ms) -Время ожидания после окончания выполнения хоуминг +The waiting time after completing the homing sequence. -#### 1.6.1.17 Linear speed +#### 1.6.1.17 Linear Speed -Линейная скорость перемещения +The linear movement speed of the machine. -#### 1.6.1.18 Angular speed +#### 1.6.1.18 Angular Speed -Угловая скорость оборотов +The angular rotation speed of the machine. ### 1.6.1 General (19-34) ![1.6.1_b.png](/aitalmac-ui/1.6.1_b.png) -#### 1.6.1.19 No tool linear speed (for A8) +#### 1.6.1.19 No Tool Linear Speed (for A8) -Линейная скорость перемещения +The linear movement speed of the machine when no tool is loaded. -#### 1.6.1.20 No tool angular speed (for A8) +#### 1.6.1.20 No Tool Angular Speed (for A8) -Угловая скорость оборотов +The angular rotation speed of the machine when no tool is loaded. -#### 1.6.1.21 Pick point radius +#### 1.6.1.21 Pick Point Radius -Радиус точки для создания метки (крест лазера) в импортируемом файле. +The radius of the point created as a marker (laser cross) in the imported file. -#### 1.6.1.22 Laser x offset +#### 1.6.1.22 Laser X Offset -Расстояние смещения лазера по оси Х +The laser's offset distance along the X-axis. -#### 1.6.1.23 Laser y offset +#### 1.6.1.23 Laser Y Offset -Расстояние смещения лазера по оси У +The laser's offset distance along the Y-axis. -#### 1.6.1.24 Table corner X point (G56) +#### 1.6.1.24 Table Corner X Point (G56) -Выбор системы координат для угла верстака по X оси +The coordinate system selection for the table corner along the X-axis. -#### 1.6.1.25 Table corner Y point (G56) +#### 1.6.1.25 Table Corner Y Point (G56) -Выбор системы координат для угла верстака по Y оси +The coordinate system selection for the table corner along the Y-axis. #### 1.6.1.26 X Parking Position -Координаты по оси Х для парковки станка с безопасное положение +The X-axis coordinates for parking the machine in a safe position. #### 1.6.1.27 Y Parking Position -Координаты по оси Y для парковки станка с безопасное положение +The Y-axis coordinates for parking the machine in a safe position. #### 1.6.1.28 Z Safe Position -Расстояние позиции безопасности по оси Z +The safety position distance along the Z-axis. #### 1.6.1.29 B Safe Position -Угол позиции безопасности по оси B +The safety position angle along the B-axis. -#### 1.6.1.30 C safe Position +#### 1.6.1.30 C Safe Position -Угол позиции безопасности по оси C +The safety position angle along the C-axis. -#### 1.6.1.31 V safe Position +#### 1.6.1.31 V Safe Position -Угол позиции безопасности по оси V +The safety position angle along the V-axis. -#### 1.6.1.32 Z fingerbit probe start +#### 1.6.1.32 Z Fingerbit Probe Start -Координата по оси Z для начала замедленного опускания головы станка до зонда для замера длины установленной фрезы. +The Z-axis coordinate for the start of the slow descent to the probe for measuring the installed tool's length. -#### 1.6.1.33 Z fingerbit probe end +#### 1.6.1.33 Z Fingerbit Probe End -Координата по оси Z для окончания опускания головы станка до зонда для замера длины установленной фрезы. +The Z-axis coordinate for the end of the descent to the probe for measuring the installed tool's length. -#### 1.6.1.34 Fingerbit probe B safe +#### 1.6.1.34 Fingerbit Probe B Safe -Угол положения по оси В для выполнения команды измерения длины фрезы с помощью зонда +The B-axis angle position for performing the tool length measurement command using the probe. ### 1.6.1 General (35-50) @@ -1888,67 +1891,67 @@ Choosing the file format for downloading the G-code program #### 1.6.1.35 Blade probe C safe -Угол положения по оси С для выполнения команды измерения диаметра лезвия с помощью зонда +The C-axis angle for performing the blade diameter measurement using the probe. #### 1.6.1.36 Z blade probe start -Координата по оси Z для начала замедленного опускания головы станка до зонда для замера диаметра установленного лезвия. +The Z-axis coordinate for starting the slow descent of the machine head to the probe for measuring the blade diameter. #### 1.6.1.37 Z blade probe end -Координата по оси Z для окончания опускания головы станка до зонда для замера диаметра установленного лезвия. +The Z-axis coordinate for ending the descent of the machine head to the probe for measuring the blade diameter. #### 1.6.1.38 Blade probe x position -Координата положения зонда по оси Х +The X-axis coordinate of the probe. #### 1.6.1.39 Blade probe y position -Координата положения зонда по оси У +The Y-axis coordinate of the probe. #### 1.6.1.40 Blade probe z position -Координата зонда по оси Z +The Z-axis coordinate of the probe. #### 1.6.1.41 Blade probe down feed -Скорость подачи при выполнении замера диаметра лезвия +The feed rate for performing the blade diameter measurement. #### 1.6.1.42 Table x point -Координата крайней точки (угла) стола по оси Х +The X-axis coordinate of the table corner point. #### 1.6.1.43 Table y point -Координата крайней точки (угла) стола по оси Y +The Y-axis coordinate of the table corner point. #### 1.6.1.44 Table width -Ширина стола +The width of the table. #### 1.6.1.45 Table height -Высота стола +The height of the table. #### 1.6.1.46 Resolution -Вкладка выбора разрешения изображения +The tab for selecting image resolution. #### 1.6.1.47 Use internet camera -Использование или отключить сетевую камеру +Enables or disables the use of a network camera. #### 1.6.1.48 Picture count (work for single host) -Выбор необходимого количества снимков. +Specifies the number of pictures to be taken. #### 1.6.1.49 Old camera -Активна или неактивен. +Indicates whether the old camera is active or inactive. #### 1.6.1.50 Take X0 image position -Координата по оси X для создания фото +The X-axis coordinate for taking a photo. ### 1.6.1 General (51-65) @@ -1956,79 +1959,79 @@ Choosing the file format for downloading the G-code program #### 1.6.1.51 Take Y0 image position -Координата по оси Y для создания фото +The Y-axis coordinate for taking a photo. #### 1.6.1.52 Take X1 image position -Координата по оси X для создания фото +The X-axis coordinate for taking a photo. #### 1.6.1.53 Take Yl image position -Координата по оси Y для создания фото +The Y-axis coordinate for taking a photo. #### 1.6.1.54 Take X2 image position -Координата по оси X для создания фото +The X-axis coordinate for taking a photo. #### 1.6.1.55 Take Y2 image position -Координата по оси Y для создания фото +The Y-axis coordinate for taking a photo. #### 1.6.1.56 Take X3 image position -Координата по оси X для создания фото +The X-axis coordinate for taking a photo. #### 1.6.1.57 Take Y3 image position -Координата по оси Y для создания фото +The Y-axis coordinate for taking a photo. #### 1.6.1.58 Wait time for take picture -Время ожидания для подготовки оборудования перед снимком +The waiting time for equipment preparation before taking a picture. -#### 1.6.1.59 Piture Scale for take picture +#### 1.6.1.59 Picture Scale for take picture -Масштаб изображения для сохранения и импорта +The scale of the image for saving and importing. #### 1.6.1.60 Safety above the stone -Расстояние безопасности над материалом +The safety clearance above the material. #### 1.6.1.61 Wood Thickness -Толщина настила верстака +The thickness of the workbench surface. #### 1.6.1.62 Plunge into the wood -Величина глубины погружения режущего инструмента в верстак +The depth of the cutting tool's plunge into the workbench. #### 1.6.1.63 Under wood table Z position -Координата по оси Z положения над столом +The Z-axis coordinate for the position below the workbench. #### 1.6.1.64 Stone thickness -Stone thickness +The thickness of the stone material. #### 1.6.1.65 Vacuum 1 x offset -Координата смещения вакуумной присоски (1) относительно центра вращения по оси Х +The X-axis offset of vacuum cup 1 relative to the center of rotation. ### 1.6.1 General (66-81) ![1.6.1_e.png](/aitalmac-ui/1.6.1_e.png) -#### 1.6.1.66 Vacuum 1 y offset +#### 1.6.1.66 Vacuum 1 Y Offset + +The Y-axis offset of vacuum cup 1 relative to the center of rotation. -Координата смещения вакуумной присоски (1) относительно центра вращения по оси Y +#### 1.6.1.67 Vacuum 1 Width -#### 1.6.1.67 Vacuum 1 width - -Ширина вакуумной присоски (1) +The width of vacuum cup 1. -#### 1.6.1.68 Vacuum 1 height +#### 1.6.1.68 Vacuum 1 Height -Высота вакуумной присоски (1) +The height of vacuum cup 1. #### 1.6.1.69 Vacuum 2 x offset @@ -2084,9 +2087,9 @@ Stone thickness #### 1.6.1.93 Vacuum 8 height -#### 1.6.1.94 Vacuum safety over stone +#### 1.6.1.94 Vacuum Safety Over Stone -Расстояние безопасности вакуумных присосок над камнем +The safety clearance distance of vacuum cups above the stone material. #### 1.6.1.95 Vacuum Z position