diff --git a/AitalMAC-UI.md b/AitalMAC-UI.md index e485fd7..e4e6317 100644 --- a/AitalMAC-UI.md +++ b/AitalMAC-UI.md @@ -1340,43 +1340,43 @@ The input signal on the control card is not assigned #### 1.5.1.81 81 [ECAT.16.1] TILTER VACUUM 1 IN PRESSURE -The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and move the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum. +The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and flipping the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum. #### 1.5.1.82 82 [ECAT.16.2] TILTER VACUUM 2 IN PRESSURE -The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and move the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum. +The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and flipping the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum. #### 1.5.1.83 83 [ECAT.16.3] TILTER VACUUM 3 IN PRESSURE -The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and move the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum. +The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and flippinf the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum. #### 1.5.1.84 84 [ECAT.16.4] TILTER VACUUM 4 IN PRESSURE -The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and move the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum. +The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and flipping the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum. #### 1.5.1.85 85 [ECAT.16.5] TILTER VACUUM 5 IN PRESSURE -The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and move the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum. +The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and flipping the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum. #### 1.5.1.86 86 [ECAT.16.6] TILTER VACUUM 6 IN PRESSURE -The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and move the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum. +The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and flipping the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum. #### 1.5.1.87 87 [ECAT.16.7] TILTER VACUUM 7 IN PRESSURE -The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and move the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum. +The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and flipping the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum. #### 1.5.1.88 88 [ECAT.16.8] TILTER VACUUM 8 IN PRESSURE -The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and move the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum. +The input signal from the vacuum monitoring sensor on the suction cups indicates whether there is a vacuum present or not. If the vacuum is created on a suction cup, it is possible to lift and flipping the material on the workbench. If not, a signal will appear to check the suction cup with the number where there is no vacuum. #### 1.5.1.89 89 [ECAT.16.9] TILTER AT 0A° -The input signal from the position sensor of the additional vacuum suction cups. The suction cups are raised and the machine can perform cutting and milling work. +The input signal comes from the position sensor of the additional vacuum suction cups. The suction cups are lifted and rotated to flip the material. #### 1.5.1.90 90 [ECAT.16.10] TILTER AT 180A° -The input signal from the position sensor of the additional vacuum suction cups. The suction cups are lowered and the machine can perform work on moving the material on the workbench. +The input signal from the position sensor of the additional vacuum suction cups. The suction cups are lowered and the machine can perform work on flipping the material on the workbench. #### 1.5.1.91 91 [ECAT.16.11] FLIPPER SAFETY @@ -1408,12 +1408,20 @@ The input signal on the control card is not assigned #### 1.5.1.97 REMOTE SPD+ +The input signal is a change in the speed of the spindle as a percentage of its initial speed. + #### 1.5.1.98 REMOTE BLADE ON +Input signal for turning on the spindle from the remote control + #### 1.5.1.99 REMOTE SPD- +The input signal is used to reduce the speed of the spindle as a percentage of its initial speed. + #### 1.5.1.100 REMOTE CONFIRM +The input signal for connecting the remote control + #### 1.5.1.101 REMOTE Y+ An input signal to enable the movement of the machine in a positive direction along the Y-axis using the remote control. @@ -1449,7 +1457,7 @@ An input signal to enable the movement of the machine in a positive direction al ### 1.5.2 OUTPUT (1-32) ![1.5.2_a.png](/aitalmac-ui/1.5.2_a.png) -A tab with the output signals from the main modules and components of the machine. The operator can use this tab to check the operation of selected commands, see how the machine is performing, and, if necessary, make adjustments. +A tab with the output signals from the main modules and components of the machine. The operator can use this tab to check the operation of selected commands, see how the machine is performing, and, if necessary, make adjustments.Care must be taken when using the output signals, because the commands are forced and do not match the safe positions of the machine. #### 1.5.2.1 01 [ECAT.13.01] ENABLE MACHINE @@ -1461,6 +1469,8 @@ Resets (reboots) the camera used for taking images of material on the workbench. #### 1.5.2.3 03 [ECAT.13.03] WATERJET ENABLE +Activates the water jet. This signal is also given when the machine is turned on from the operator's menu. + #### 1.5.2.4 04 [ECAT.13.04] VACUUM PUMP Activates the vacuum pump, creating a vacuum in the system. This signal is necessary for testing all vacuum suction cups. Each suction cup can be tested individually by activating its respective output signal. @@ -1475,14 +1485,20 @@ Activates the automatic lubrication pump. The pump normally operates at set inte #### 1.5.2.7 07 [ECAT.13.07] CHILLER SWITCH +Activating chiller shutdown + #### 1.5.2.8 08 [ECAT.13.08] TABLE SLOW SWITCH VALVE +??? + #### 1.5.2.9 09 [ECAT.13.09] SLAB WASH Activates the material cleaning system. This opens the water supply valve for cleaning nozzles. #### 1.5.2.10 10 [ECAT.13.10] WATERJET GUN +??? + #### 1.5.2.11 11 [ECAT.13.11] INTERNAL WATER Enables water flow through the spindle center for milling operations. Activating this signal opens the respective water and air supply valves. @@ -1585,238 +1601,435 @@ Activates the yellow light on the control panel. The yellow light signals that t #### 1.5.2.35 35 [ECAT.19.03] GREEN LIGHT +Activates the green light on the control panel. A green light warns the operator when the machine is working. + #### 1.5.2.36 36 [ECAT.19.04] WHITE LIGHT +Activates the white light on the control panel. A white light warns the operator about making machine settings + #### 1.5.2.37 37 [ECAT.19.05] TCP LIGHT +Активируется зелёная подсветка выключателя. Зелёный свет показывает что интерполяции включена. + #### 1.5.2.38 38 [ECAT.19.06] NONE +The output signal on the control board is not set + #### 1.5.2.39 39 [ECAT.19.07] NONE +The output signal on the control board is not set + #### 1.5.2.40 40 [ECAT.19.08] NONE +The output signal on the control board is not set + #### 1.5.2.41 41 [ECAT.19.09] NONE +The output signal on the control board is not set + #### 1.5.2.42 42 [ECAT.19.10] NONE +The output signal on the control board is not set + #### 1.5.2.43 43 [ECAT.19.11] NONE +The output signal on the control board is not set + #### 1.5.2.44 44 [ECAT.19.12] NONE +The output signal on the control board is not set + #### 1.5.2.45 45 [ECAT.19.13] NONE +The output signal on the control board is not set + #### 1.5.2.46 46 [ECAT.19.14] NONE +The output signal on the control board is not set + #### 1.5.2.47 47 [ECAT.19.15] NONE +The output signal on the control board is not set + #### 1.5.2.48 48 [ECAT.19.16] NONE +The output signal on the control board is not set + ### 1.5.3 DOUT (1-16) ![1.5.3.png](/aitalmac-ui/1.5.3.png) #### 1.5.3.1 1 [ECAT.15.01] FLIPPER VAC 1 +Activates the vacuum suction cup (1) on the tile flip module. + #### 1.5.3.2 42 [ECAT.15.02] FLIPPER VAC 2 +Activates the vacuum suction cup (2) on the tile flip module. + #### 1.5.3.3 43 [ECAT.15.03] FLIPPER VAC 3 +Activates the vacuum suction cup (3) on the tile flip module. + #### 1.5.3.4 44 [ECAT.15.04] FLIPPER VAC 4 +Activates the vacuum suction cup (4) on the tile flip module. + #### 1.5.3.5 45 [ECAT.15.05] FLIPPER VAC 5 +Activates the vacuum suction cup (5) on the tile flip module. + #### 1.5.3.6 46 [ECAT.15.06] FLIPPER VAC 6 +Activates the vacuum suction cup (6) on the tile flip module. + #### 1.5.3.7 47 [ECAT.15.07] FLIPPER VAC 7 +Activates the vacuum suction cup (7) on the tile flip module. + #### 1.5.3.8 48 [ECAT.15.08] FLIPPER VAC 8 +Activates the vacuum suction cup (8) on the tile flip module. + #### 1.5.3.9 49 [ECAT.15.09] FLIPPER FLIP +Активирует поворот модуля на 180°. Команда выполнится игнорируя безопасность. Оператор должен внимательно следить за положением модуля. + #### 1.5.3.10 59 [ECAT.15.10] NONE +The output signal on the control board is not set + #### 1.5.3.11 60 [ECAT.15.11] NONE +The output signal on the control board is not set + #### 1.5.3.12 61 [ECAT.15.12] NONE +The output signal on the control board is not set + #### 1.5.3.13 62 [ECAT.15.13] NONE +The output signal on the control board is not set + #### 1.5.3.14 63 [ECAT.15.14] NONE +The output signal on the control board is not set + #### 1.5.3.15 64 [ECAT.15.15] NONE +The output signal on the control board is not set + #### 1.5.3.16 65 [ECAT.15.16] NONE +The output signal on the control board is not set + ### 1.5.4 SERVICE ![1.5.4.png](/aitalmac-ui/1.5.4.png) +Данные работы станка и моторов, время работы (моточасы) Для своевременно обслуживания станка. #### 1.5.4.1 MACHINE HOURS +Общее время работы станка от первого включения до последнего выключения. + #### 1.5.4.2 SPINDLE HOURS +Общее время работы шпинделя от первого включения до последнего выключения. + #### 1.5.4.3 WATERJET HOURS +Общее время работы мотора от первого включения до последнего выключения. + ## 1.6 Parameters ![1.6.png](/aitalmac-ui/1.6.png) +Основные параметры станка. Разделены на пять вкладок. ### 1.6.1 General (1-18) ![1.6.1_a.png](/aitalmac-ui/1.6.1_a.png) +Главные параметры станка. #### 1.6.1.1 Language +Выбор языка интерфейса. Можно активировать один из доступных языков. + #### 1.6.1.2 Machine +Выбор станка для настройки параметров. Нужно активировать нужную модель станка. + #### 1.6.1.3 Write debug info to the debug.txt +Enabling or disabling the "Write debug information to a file" debug.txt + #### 1.6.1.4 Lock page +Enabling or disabling the ability to block a page + #### 1.6.1.5 Use aitalmac remote +Включение или отключение возможности использовать пульт дистанционного управления aitalmac + #### 1.6.1.6 Auto accept pnc program #### 1.6.1.7 Auto clean pnc program #### 1.6.1.8 Check B angle when Z down without Blade +Enabling or disabling the ability check B angle when Z down without Blade + #### 1.6.1.9 Image position is without KINS #### 1.6.1.10 Debug mode #### 1.6.1.11 GCode type for gcode page +Choosing the file format for downloading the G-code program + #### 1.6.1.12 Accent Color +Выбор акцентного цвета для отображения в меню + #### 1.6.1.13 Primary Color +Выбор основного цвета для отображения в меню + #### 1.6.1.14 CNC communication rate (ms) +Скорость коммуникации модулей управления + #### 1.6.1.15 Wait time of after machine on (s) +Время ожидания перед использованием станка после включения. (время для самотестирования и проверки) + #### 1.6.1.16 Wait time of after finish homing (ms) +Время ожидания после окончания выполнения хоуминг + #### 1.6.1.17 Linear speed +Линейная скорость перемещения + #### 1.6.1.18 Angular speed +Угловая скорость оборотов + ### 1.6.1 General (19-34) ![1.6.1_b.png](/aitalmac-ui/1.6.1_b.png) #### 1.6.1.19 No tool linear speed (for A8) +Линейная скорость перемещения + #### 1.6.1.20 No tool angular speed (for A8) +Угловая скорость оборотов + #### 1.6.1.21 Pick point radius +Радиус точки для создания метки (крест лазера) в импортируемом файле. + #### 1.6.1.22 Laser x offset +Расстояние смещения лазера по оси Х + #### 1.6.1.23 Laser y offset +Расстояние смещения лазера по оси У + #### 1.6.1.24 Table corner X point (G56) +Выбор системы координат для угла верстака по X оси + #### 1.6.1.25 Table corner Y point (G56) +Выбор системы координат для угла верстака по Y оси + #### 1.6.1.26 X Parking Position +Координаты по оси Х для парковки станка с безопасное положение + #### 1.6.1.27 Y Parking Position +Координаты по оси Y для парковки станка с безопасное положение + #### 1.6.1.28 Z Safe Position +Расстояние позиции безопасности по оси Z + #### 1.6.1.29 B Safe Position +Угол позиции безопасности по оси B + #### 1.6.1.30 C safe Position +Угол позиции безопасности по оси C + #### 1.6.1.31 V safe Position +Угол позиции безопасности по оси V + #### 1.6.1.32 Z fingerbit probe start +Координата по оси Z для начала замедленного опускания головы станка до зонда для замера длины установленной фрезы. + #### 1.6.1.33 Z fingerbit probe end +Координата по оси Z для окончания опускания головы станка до зонда для замера длины установленной фрезы. + #### 1.6.1.34 Fingerbit probe B safe +Угол положения по оси В для выполнения команды измерения длины фрезы с помощью зонда + ### 1.6.1 General (35-50) ![1.6.1_c.png](/aitalmac-ui/1.6.1_c.png) #### 1.6.1.35 Blade probe C safe +Угол положения по оси С для выполнения команды измерения диаметра лезвия с помощью зонда + #### 1.6.1.36 Z blade probe start +Координата по оси Z для начала замедленного опускания головы станка до зонда для замера диаметра установленного лезвия. + #### 1.6.1.37 Z blade probe end +Координата по оси Z для окончания опускания головы станка до зонда для замера диаметра установленного лезвия. + #### 1.6.1.38 Blade probe x position +Координата положения зонда по оси Х + #### 1.6.1.39 Blade probe y position +Координата положения зонда по оси У + #### 1.6.1.40 Blade probe z position +Координата зонда по оси Z + #### 1.6.1.41 Blade probe down feed +Скорость подачи при выполнении замера диаметра лезвия + #### 1.6.1.42 Table x point +Координата крайней точки (угла) стола по оси Х + #### 1.6.1.43 Table y point +Координата крайней точки (угла) стола по оси Y + #### 1.6.1.44 Table width +Ширина стола + #### 1.6.1.45 Table height +Высота стола + #### 1.6.1.46 Resolution +Вкладка выбора разрешения изображения + #### 1.6.1.47 Use internet camera +Использование или отключить сетевую камеру + #### 1.6.1.48 Picture count (work for single host) +Выбор необходимого количества снимков. + #### 1.6.1.49 Old camera +Активна или неактивен. + #### 1.6.1.50 Take X0 image position +Координата по оси X для создания фото + ### 1.6.1 General (51-65) ![1.6.1_d.png](/aitalmac-ui/1.6.1_d.png) #### 1.6.1.51 Take Y0 image position +Координата по оси Y для создания фото + #### 1.6.1.52 Take X1 image position +Координата по оси X для создания фото + #### 1.6.1.53 Take Yl image position +Координата по оси Y для создания фото + #### 1.6.1.54 Take X2 image position +Координата по оси X для создания фото + #### 1.6.1.55 Take Y2 image position +Координата по оси Y для создания фото + #### 1.6.1.56 Take X3 image position +Координата по оси X для создания фото + #### 1.6.1.57 Take Y3 image position +Координата по оси Y для создания фото + #### 1.6.1.58 Wait time for take picture +Время ожидания для подготовки оборудования перед снимком + #### 1.6.1.59 Piture Scale for take picture +Масштаб изображения для сохранения и импорта + #### 1.6.1.60 Safety above the stone +Расстояние безопасности над материалом + #### 1.6.1.61 Wood Thickness +Толщина настила верстака + #### 1.6.1.62 Plunge into the wood +Величина глубины погружения режущего инструмента в верстак + #### 1.6.1.63 Under wood table Z position +Координата по оси Z положения над столом + #### 1.6.1.64 Stone thickness +Stone thickness + #### 1.6.1.65 Vacuum 1 x offset +Координата смещения вакуумной присоски (1) относительно центра вращения по оси Х + ### 1.6.1 General (66-81) ![1.6.1_e.png](/aitalmac-ui/1.6.1_e.png) #### 1.6.1.66 Vacuum 1 y offset +Координата смещения вакуумной присоски (1) относительно центра вращения по оси Y + #### 1.6.1.67 Vacuum 1 width + +Ширина вакуумной присоски (1) #### 1.6.1.68 Vacuum 1 height +Высота вакуумной присоски (1) + #### 1.6.1.69 Vacuum 2 x offset #### 1.6.1.70 Vacuum 2 y offset @@ -1873,6 +2086,8 @@ Activates the yellow light on the control panel. The yellow light signals that t #### 1.6.1.94 Vacuum safety over stone +Расстояние безопасности вакуумных присосок над камнем + #### 1.6.1.95 Vacuum Z position #### 1.6.1.96 Vacuum down feed